Hvlp Spray Gun Tip Sizes
Hvlp spray gun tip sizes. Use your fan-control knob located on top of your sprayer for this setting. As a general guide these are the recommended airless tip sizes. HVLP SPRAY GUN NOZZLE RECOMMENDATIONS LPH400LV LPH100LPH300LV AZ3HV Primers DX1791 Nozzle Size 13 MM 12-14 MM DPX170171 Air Pressure 16 PSI 14 PSI DP LF Air Comsumption 95 CFM 71 CFM Primer Surfacers K36 K38 K93 Nozzle Size 13 MM 14 MM 18 MM NCP 250 Air Pressure 16 PSI 14 PSI 29 PSI NCP270271272 Air Comsumption 95 CFM 71 CFM 133 CFM.
When purchasing a paint gun make sure it can accommodate the needle size you are looking for. Thinner paints run the risk of orange peel though because they. Start with the larger size and see how you like it.
If you are spraying the same material with automated spray HVLP a 008mm to 10mm tip size is recommended. Below we give a list of the common size spray tips and whenwhere to use them. For starters ensure your spray gun is about six inches high.
This limits bounceback and wasted paint as more paint is likely to stick to the surface that youre painting. The heavier the coating the larger the nozzle size should be. 13 mm or 14 mm nozzle tips are very universal and these cover most of the materials we use on the industrial side.
Since you are up for an HVLP gun you must know that the spray gun comes with a gun tip. How to Select the Right Tip for Your Paint Gun 12mm 13mm. 5 18mm - Ideal for larger surfaces and thicker layers.
Basecoats should be sprayed. As an example primers are commonly thicker compared to the top coat and may require a 17 or 18 mm tip. 12-13MM- These nozzle and tip combinations are the most fine and therefore work well for thinner coatings.
Clear coats are not commonly used in industrial painting so this is a common process used to maximize gloss. A general rule of thumb is.
Below we give a list of the common size spray tips and whenwhere to use them.
If you are spraying the same material with automated spray HVLP a 008mm to 10mm tip size is recommended. And dont move too quickly or in PRAYING LATEX PAINT atex paint the kind normally used with a brush or roller is a difficult medium for most spray guns but you e thinned for HVLP spraying and typically 5. For starters ensure your spray gun is about six inches high. Catalyzed lacquers primers varnish urethanes enamel industrial coating higher viscosity sealers polyurethane oil based paints epoxy enamels plastic adhesives floor paving paints latex walls splatter paints and multi fleck paints. Hold the gun the proper distance from the work. The material push button is also located on top of your spray gun. 13 mm or 14 mm nozzle tips are very universal and these cover most of the materials we use on the industrial side. Below we give a list of the common size spray tips and whenwhere to use them. While most guns spray paint at around 50 PSI most HVLP guns only spray at around 10 PSI.
The size of the airless spray tip you need depends on the type of paint you are spraying. If you are spraying the same material with automated spray HVLP a 008mm to 10mm tip size is recommended. While most guns spray paint at around 50 PSI most HVLP guns only spray at around 10 PSI. 5 18mm - Ideal for larger surfaces and thicker layers. 009 -013 Oil Based Paint. For starters ensure your spray gun is about six inches high. 13 mm or 14 mm nozzle tips are very universal and these cover most of the materials we use on the industrial side.
Post a Comment for "Hvlp Spray Gun Tip Sizes"